spotlights-tubelight

Tubelight^{LV DUAL FIX}
			SH Adjustable Shelf Holders / Supports available. Dual Fix Tubelights can be supplied with any number of Shelf Supports attached. The Shelf supports can be used to hold glass shelves in position or fix Tubelight Dual Fix onto shelves.
"Tubelight LV Spotlights can be manufactured and supplied to accept any of the lamps shown below.."
MR8 12V G4 20W or 35W Halogen Diameter - 25mm	MR11 12V G4 20W or 35W Halogen Diameter - 35mm	MR16 12V G5.3 20W, 35W or 50W Halogen Diameter - 50mm	MR11 12V G4 1.1W LED Cluster Diameter - 35mm	MR16 12V G5.3 1.5W LED Cluster Diameter - 50mm	MR16 12V G5.3 Triple High Power 4W & 5W White & Warm White LED Diameter - 50mm
MR11 GU4 Spotlights			MR16 GU5.3 Spotlights

S112 Cap - GU4 Lamp - 12V MR8 or MR11 Max Wattage - 35W			S122 Cap - GU5.3 Lamp - 12V MR16 Max Wattage - 50W

S111 (Cowled) Cap - GU4 Lamp - 12V MR11 Max Wattage - 20W			S121 (Cowled) Cap - GU5.3 Lamp - 12V MR16 Max Wattage - 20W
Tube
TUBE DIAMETER - 9.6mm - 3/8" Display Lighting can manufacture and supply Tubelight LV Dual Fix in lengths between: 150mm - 2000mm (Max 5 Spotlights)
Bases / Fixings

RF10 Rear Fix Base Plate Diameter - 22mm Fixing - M10 thread c/w M10 half nut & washer.			FF10 Front Fix Base Plate Diameter - 30mm Fixing - 2 concealed screws

CP10 Ceiling Plate Diameter - 54mm Fixing - 2 concealed screws			GF10 Glass Fixer Diameter - 20mm Thread - M5 (Drill 6mm - 8mm hole in glass) (For fixing top of Dual Fix Tubelight to Glass only, maximum glass thickness 12mm)

Information for ordering Dual Fix Tubelight Display Luminaires:

TD3.500.S112.03
+ RF10.03 (Bottom) & GF10.03 (Top)

When ordering Tubelight please use the following codes:
1. Configuration

e.g.
TD2 - 2 x 12V Spotlights
TD3 - 3 x 12V Spotlights
TD4 - 4 x 12V Spotlights
TD5 - 5 x 12V Spotlights
2. Overall height

e.g. 500 (150mm - 2000mm)

(Measured from the face of the bottom panel to underside of top panel)

3. Spotlights

e.g. S112 (Any of the 4 types of 12V spotlights pictured above.)

4. Finish

.03 - Chrome

.05 - Brushed Chrome/Stainless Steel Effect
( .01 - White, .02 Black, .04 Brass can be supplied but have been classified as non standard finishes and will incur a setup charge to cover extra costs involved.)
5. Base Fixing
e.g. RF10 - Rear Fix Base Plate (Any of the Bases pictured above except GF10)
6. Top Fixing
e.g. GF10 - Glass Fixer (Any of the Bases pictured above)

It is, in our opinion, through years of experience illuminating cabinets and showcases, that using 50W lamps can raise the ambient temperature to very high levels and can be detrimental to both the merchandise on display and also to any electronic control gear used to power the 12V luminaires. It is for this reason that we would strongly recommend that no higher wattage lamps than 35W are used within this type of application and we cannot guarantee luminaires using 50W lamps.